Filter By:
- Show More Brands
- Show Fewer Brands
- Show More Sizes
- Show Fewer Sizes
Parts & Accessories

$600.00
Choose to ride even faster by using CeramicSpeed Hub Bearings in your wheels. The DT Swiss-3 wheel kit fits 240s Disc hubs. Other kits are available for DT 240s rim brake hubs, and DT180 as well.
The high velocity of wheel bearings means that bearing friction can have a huge impact on performance. CeramicSpeed Wheel Bearings have a proven lifespan, which is 3-5 times longer than standard wheel bearings.
In The Box:
- 2 x 61903/18 bearings
- 2 x 61802 bearings
- 2 x 61902 bearings
- 10ml syringe of CeramicSpeed All Round Grease
- Sticker sheet
Remember to add grease and mount seals before installation.

$600.00
Optimize your Zipp wheels with CeramicSpeed Hub Bearings to benefit from reduced friction and increased performance. The result is higher speed with the same effort as well as a higher top speed. CeramicSpeed Wheel Bearings have a proven lifetime, which is 3-5 times longer than standard bearings.
All components are optimized for low friction and prolonged lifetime.
This wheel kit is compatible with 1st generation non-disc Zipp NSW (before mid-2018).
In The Box
- 4 x 61803 bearings
- 1 x 61903 bearing
- 1 x 61804 bearing
- 10ml syringe of CeramicSpeed All Round Grease
- Sticker sheet

$543.50
Make it more aerodynamic – this nipple is hidden inside the rim.
DT Hidden Nipples are designed for high-profile rims, in which the inverted design is essential for optimum precision. They are very light and hidden on the inside of the rim: perfectly suited for high aero wheels. The nipples will align perfectly due to their spherical contact surface.
- Weight: 22g for 64 nipples

$487.00
Convert your ISO, ISO B, or ISO Superboost DH rear hub to a Shimano Micro Spline compatible driveshell. The conversion kit is complete with an axle, adjustment clamp, driveshell, and all driveshell internals for a plug-and-play swap.
Micro Spline Driveshell Instructions
- Compatible with Shimano Micro Spline cassettes; XTR, XT, and SLX
- Compatible with ISO 142x12mm, ISO B 148x12mm, and ISO Superboost DH 157x12mm rear hubs.

$390.00
- Kits include Freehub body with CeramicSpeed bearings pre-installed for easy installation onto the wheel
- Measurable wattage savings between 1.5 and 9 watts per bearing set, depending on the level and condition of your existing bearings

$390.00
- Lowest resistance hybrid ceramic (ceramic balls and steel cages) available
- Measurable wattage savings between 1.5 and 9 watts per bearing set, depending on the level and condition of your existing bearings
- Kits include Freehub body with CeramicSpeed

$19.11 - $236.20
Developed for short spokes with a large deflection angle.
DT Pro Head nipples are designed for short spokes with a large angle of deflection, such as for e-bike use. Through the spherical contact surface, the nipple aligns automatically with the angle of the spoke, which leads to consistent power transmission. Note: brass nipples are not approved for children's products in the USA. See attached warning! All-brass nipples are recommended for e-bike use.
- Weight: starting at 59g for 64 nipples.

$223.00
- Hub Cognition V2 Axial Clutch Kit
- Disc brake/rim brake
- Includes: ratchet shell & driver, sylomer spring assembly & seal cap)

$220.00
- Replacement freehub bodies include pawls and springs pre-installed
- M-Pulse hubs: six pawls are equipped with Neodymium magnets engaging every 1.66 deg
- E-Sync hubs: fast 8.18 deg engagement with reinforced high-torque pawls
- HG 11sp road FH body

$220.00
- Replacement freehub bodies include pawls and springs pre-installed
- M-Pulse hubs: six pawls are equipped with Neodymium magnets engaging every 1.66 deg
- E-Sync hubs: fast 8.18 deg engagement with reinforced high-torque pawls
- HG 11sp road FH body

$220.00
- Replacement freehub bodies include pawls and springs pre-installed
- M-Pulse hubs: six pawls are equipped with Neodymium magnets engaging every 1.66 deg
- E-Sync hubs: fast 8.18 deg engagement with reinforced high-torque pawls
- HG 11sp road FH body

$206.00
Zipp Speed Weaponry Rear Axle Conversion Kit
- Not to be used on 188 V6 or earlier rear hubs
- Only to be used to convert Zipp's 188 V7 10-speed rear hubs to 11-speed

$194.00
Wheel Freehub Kit SRAM XDR for Super 9RB
- Compatible only with the Super 9
- Compatible With: WH-SP9-CCR-A1

$11.50 - $140.00
We designed Teravail tubeless tape for no-hassle installation. Its slight stretch allows the tape to easily conform to your rims. The translucent material shows you exactly where the tape makes contact. It's tacky enough to prevent shifting but easy to pull up if needed, and it won't leave residue on your rims.
- Teravail Tubeless Tape comes in a variety of widths to fit almost any rim.
- Teravail Tubeless Tape is available in a variety of widths and roll lengths.
- Ten-meter length is enough for a single layer on approximately four wheels

$9.99 - $139.99
Looking for a super lightweight but badass tubeless sealant? Boom, you've just found it my friend! No Puncture Hassle performs under the most brutal race conditions. The cutting-edge microfiber molecules fill the bigger holes and tears, whilst the advanced latex forms a strong seal instantly. The formula also contains a unique UV detection system that highlights any punctures you haven’t seen during your ride.
Developed with the world's top downhillers and pro peloton teams, to give you the finest tire sealant available. It's non-corrosive and easily washes off with water. Compatible with tubeless ready and full UST wheels/tires, No Puncture Hassle works from 15psi-120psi and temperatures from -20°C to +50°C. Our pouch is designed to fit your Presta valve perfectly and is ideal to add to your toolkit or ride pack for emergency top ups on the go!
- For Downhill, Enduro and Road tires
- Seals tears and holes up to 6mm
- Contains UV puncture detection
- Won't dry out or ball
- Works from 15psi-120psi and temperatures from -20°C to +50°C
- Biodegradable

$130.00
Stan's original Neo hub has evolved to be stronger and more reliable than ever. The additional stress of larger cassette cogs, more capable bikes, and even more challenging trails led to the creation of the Neo with Speedsync.
This CNC machined Speedsync freehub is a direct replacement for your Neo hub and includes pawls, springs, pawl retaining ring, and 2 red freehub spacers. Bearings are pre-installed.
Note:
- Singlespeed freehub cannot be used to convert a hub originally set up with a Shimano or Sram XD freehub to SS. This freehub is only to be used with Stan's Neo SS hubs.
- OneUp freehub WILL NOT WORK with a SRAM cassette or Shimano cassette without a One Up Shark Cluster.

$119.99
- 6 pawl/54 point/6.6-degree engagement
- Cassette bodies for Elite Series CX/GX/MT/FB-1110 hubs
- Sealed bearings

$119.99
- 6 pawl full engagement/27 point/13.3-degree engagement
- Cassette bodies for Elite Series CX/GX/MT/FB-1110 hubs
- Sealed bearings

$115.50
125 piece assortment of precision machined axle spacers (0.5mm to 5mm thickness). - Outside Diameter of Spacers: 16mm - Inside Diameter of Spacers: 10mm Kit includes: - (10) - 0.5mm thick spacers - (30) - 1mm thick spacers - (30) - 2mm thick spacers - (25) - 3mm thick spacers - (15) - 4mm thick spacers - (15) - 5mm thick spacers

$109.95
- Various HyperGlide freehub body assemblies for Halo freehubs
- Shimano/SRAM 8-10-speed
- Spin Doctor, Spin Doctor Pro and Spin Doctor 6-Drive parts are generally not cross compatible
- DJD and DJD-BD parts are generally not cross compatible

$108.00
Wheel Freehub Kit—(Includes Bearings & Pawls) 11/12 Speed XD—X0 HUBS/RISE 60 (B1)/ROAM 30/ROAM 40/RAIL 40/RISE XX/ROAM 50/60 (B1)
Compatible With:
HU-X0-A1, WH-RAIL-40-A1, WH-RISE-60-B1, WH-RISE-XX-A1, WH-ROAM-30-A1, WH-ROAM-40-A1, WH-ROAM-50-A1, WH-ROAM-50-B1, WH-ROAM-60-B1
Page 1 of 15
Next page